VAC TagMaster Training Module T3, Page 1 TagMaster AB Технический семинар TagMaster 2013 Настройка системы GEN4
TagMaster Training Module T3, Page 2 TagMaster AB Содержание Обзор системы Требования по установке Электросоединения и монтаж Устранение неполадок и поддержка
TagMaster Training Module T3, Page 3 TagMaster AB Обзор системы
TagMaster Training Module T3, Page 4 TagMaster AB Сетевая или автономная система В рамках сетевой системы управление и мониторинг работы одного или более считывателей осуществляется при помощи ПО, установленного на удаленном сервере. В случае автономной системы, управление и мониторинг работы считывателей осуществляется при помощи встроенного ПО. SW
TagMaster Training Module T3, Page 5 TagMaster AB Интерфейсы и протоколы (сетевая система) Сетевой интерфейс Ethernet Протокол TAGP SW Ethernet SW RS232 RS485 WatchMan Последовательные интерфейсы RS232 (двухпунктовый) RS485 (многопунктовый) Протокол ConfiTalk (WatchMan/WiseMan)
TagMaster Training Module T3, Page 6 TagMaster AB Интерфейсы для конфигурации Считыватель имеет два конфигурационных интерфейса Web-интерфейс (TCP/IP по Ethernet) Клеммный интерфейс (последовательный или SSH по Ethernet) Оба интерфейса защищены паролем и отображают идентичную информацию Интерфейсы применяются для задания стандартных параметров системы: пароли, дата и время, сетевые параметры и пр..
TagMaster Training Module T3, Page 7 TagMaster AB Подключение к считывателю Три способа подключения (для конфигурации) По сети Напрямую через Ethernet-соединение Через последовательный RS232-порт 1 2 3
TagMaster Training Module T3, Page 8 TagMaster AB Network Connection (1) The reader obtains network settings automatically using DHCP (Dynamic Host Configuration Protocol) A service discovery tool such as Bonjour (next slide) is used to find the reader on the network Network Connection PIC
TagMaster Training Module T3, Page 9 TagMaster AB Bonjour Bonjour makes it possible to find devices on a local network Bonjour is available as a plugin for Internet Explorer and built into the Safari browser Bonjour can be downloaded from (Any tool that supports the mDNS/DNS-SD protocols can be used)
TagMaster Training Module T3, Page 10 TagMaster AB Direct Ethernet Connection (2) The reader automatically uses default network settings (IP ) The PC can be configured to automatically use a suitable IP address when no DHCP server is available (next slide) Bonjour can still be used to connect to the reader (but is not needed since the IP address is known) Auto MDI/MDI-X support makes it possible to use a straight through or a crossover cable Direct Ethernet Connection
TagMaster Training Module T3, Page 11 TagMaster AB Dual Network Configurations on PC Most PCs are configured to obtain network parameters using DHCP. By specifying an alternate configuration it is possible to use fixed network parameters when no DHCP server is available. This is very convenient when connecting a reader directly to the PC! On the Start menu, click Control Panel. Click Network and Internet Connections. Click Network Connections. Right-click the local area network (LAN) or high-speed Internet connection that you want to configure and click Properties. Click Internet Protocol (TCP/IP) and click Properties. Click the Alternate Configuration tab. Internet Protocol Properties Dialog (Windows XP)
TagMaster Training Module T3, Page 12 TagMaster AB Serial RS232 Connection (3) Use a terminal program with the following settings: bps, 8 data bits, 1 stop bit, no parity, no flow control PuTTY-TE is a free terminal program with everything preconfigured for TagMasters readers. It can be downloaded from ftp://ftp.tagmaster.com Serial RS232 Connection
TagMaster Training Module T3, Page 13 TagMaster AB
TagMaster Training Module T3, Page 14 TagMaster AB Требования по установке
TagMaster Training Module T3, Page 15 TagMaster AB Компоненты системы Автоматическая радиочастотная идентификация (RFID) объектов с использованием двух компонентов: считывателя и ID-метки
TagMaster Training Module T3, Page 16 TagMaster AB Теоретическая область считывания Расстояние считывания, согласно спецификации Метка Область считывания LR-3 до 5 м LR-6 до 10 м LR-6 XL до 14 м Считыватель
TagMaster Training Module T3, Page 17 TagMaster AB Фактическая область считывания
TagMaster Training Module T3, Page 18 TagMaster AB Reader Reading lobe Tag ID-метки должны быть обращены к считывателю, то есть лицевые стороны считывателя и ID-меток должны располагаться максимально параллельно друг к другу. Основные требования по установке
TagMaster Training Module T3, Page 19 TagMaster AB Считыватели на параллельных полосах Идентификация автомобилей на многополосном проезде
TagMaster Training Module T3, Page 20 TagMaster AB Документация на продукцию Спецификации (доступны для скачивания с сайта после регистрации) Исчерпывающая техническая документация Инструкции пользователя (доступны для скачивания с сайта после регистрации) Исчерпывающая документация для пользователя
TagMaster Training Module T3, Page 21 TagMaster AB Установка решения Руководство по установке (доступно для скачивания с сайта после регистрации) Исчерпывающая информация для установки
TagMaster Training Module T3, Page 22 TagMaster AB Electrical and Mechanical Installation
TagMaster Training Module T3, Page 23 TagMaster AB Inside a LR-6 Reader
TagMaster Training Module T3, Page 24 TagMaster AB GEN4 controller board connections RelayInputsOutputs Power supply Tamper Wiegand RS485RS232Service USB Host Expansion board µSD card
TagMaster Training Module T3, Page 25 TagMaster AB GEN4 interface schematics
TagMaster Training Module T3, Page 26 TagMaster AB GEN4 power supply
TagMaster Training Module T3, Page 27 TagMaster AB Рекомендуется использовать кабели малого сопротивления, при этом длина кабелей должна быть минимальной. При закладке проводки большой длины следует использовать экранированные кабели. На одном конце, желательно на стороне контроллера, экран кабеля должен быть заземлен. Никогда не следует использовать экран соединительного кабеля для заземления силового. Для силовых и соединительных линий длиной от 10 до 100 м рекомендуется использовать экранированные кабели AWG Выбор диаметра и длины кабеля производится таким образом, чтобы исключить излишние потери напряжения при фактической токовой нагрузке. На одном конце, желательно на стороне контроллера, экран кабеля должен быть заземлен. При прокладке соединительных проводов немало внимания следует уделить тому, чтобы они находились на достаточном расстоянии от источников питания и/или не проходили в одном коробе с силовыми кабелями. Проводка
TagMaster Training Module T3, Page 28 TagMaster AB 2-wire RS485: Termination and Pull Resistors When no RS485 sender is active the bus is floating. Pull resistors at one end of the bus are recommended to create a defined state. Termination resistors should be placed at both ends of the bus if long cables and/or high communication speeds are used. DATA+ DATA- DATA+ DATA GND VCC
TagMaster Training Module T3, Page 29 TagMaster AB Удаление заглушки кабельного соединения считывателя серии LR
TagMaster Training Module T3, Page 30 TagMaster AB Удаление заглушки кабельного соединения считывателя серии LR Осторожно! За заглушкой находится печатная плата!
TagMaster Training Module T3, Page 31 TagMaster AB LR-series Cable Knockouts Dont remove the pressure balance membrane!
TagMaster Training Module T3, Page 32 TagMaster AB LR-6 Mounting Hole Layouts
TagMaster Training Module T3, Page 33 TagMaster AB UMK – Universal Mounting Kit For wall mount or pole mount
TagMaster Training Module T3, Page 34 TagMaster AB Details of the UMK
TagMaster Training Module T3, Page 35 TagMaster AB Accessories for ID-tags WinFix Classic WinFix MeM CardTape Tag Fixing HD
TagMaster Training Module T3, Page 36 TagMaster AB Troubleshooting & Support
TagMaster Training Module T3, Page 37 TagMaster AB Troubleshooting The following slides will show what you can do to find the cause of a problem – typically the reader is not faulty. If there is something wrong with the reader: There are no user servicable parts inside The reader is production tested as a complete unit Do not swap boards/parts between readers
TagMaster Training Module T3, Page 38 TagMaster AB #1: Read the Manuals All manuals can be downloaded from
TagMaster Training Module T3, Page 39 TagMaster AB Functional Check using Web Interface (1/3) Use ID-tag R/W to check if the reader reads ID-tags Remember to set Filter to Off!
TagMaster Training Module T3, Page 40 TagMaster AB Functional Check using Web Interface (2/3) Use I/O Test to check inputs and outputs
TagMaster Training Module T3, Page 41 TagMaster AB Functional Check using Web Interface (3/3) Use Spectrum Scan to find interferers
TagMaster Training Module T3, Page 42 TagMaster AB Technical Support TagMaster Technical Support offers Brief guidance via telephone, or fax Extensive support when problems require tests/trials or written reports On site and installation support on a consultancy basis Contact is best made using attaching a detailed technical description of what has happened Support can also be contacted during office hours on Phone: Fax:
TagMaster Training Module T3, Page 43 TagMaster AB Upgrading System Software
VAC TagMaster Training Module T3, Page 44 TagMaster AB Конец