Скачать презентацию
Идет загрузка презентации. Пожалуйста, подождите
Презентация была опубликована 9 лет назад пользователемМихаил Тчанников
1 Copyright DASSAULT SYSTEMES Твердотельное моделирование Продвинутый курс CATIA Тренинги Материалы Версия 5 Релиз 9 Июнь 2002 EDU-CAT-E-PDG-FF-V5R9
2 Copyright DASSAULT SYSTEMES Операция Ребро (Rib) х мерная кривая была создана при помощи инструментов модуля поверхностного моделирования
3 Copyright DASSAULT SYSTEMES Операция Паз (Slot) Профили должны быть созданы предварительно Глубина профиля должна быть НЕ больше величины радиуса
4 Copyright DASSAULT SYSTEMES Создание рёбер (Stiffeners) (1/2) Выбор контура Возможны 2 варианта для построения ребра : From Side и From Top.
5 Copyright DASSAULT SYSTEMES Создание тела по набору кривых Далее рассмотрим способы создания прямых и обратных твердых тел по набору сечений Создание прямых тел по набору кривых Обратные тела по набору кривых Сочетания Замыкающие точки
6 Copyright DASSAULT SYSTEMES Тела по набору кривых(Lofts) Рассмотрим способы создания твердых тел по набору кривых Создание прямых тел по набору кривых
7 Copyright DASSAULT SYSTEMES Что такое тело по набору кривых (Loft)? Loft – позитивное или негативное тело, созданное по двум или более плоским сечениям и направляющим кривым Направляющие стрелки обеспечивают необходимую ориентацию сечений Плоские сечения могут соединяться направляющими (Guide) или ориентирующими (Spine) кривыми Для обеспечения правильной ориентации замыкающие точки (Closing Points) в сечениях должны соответствовать друг другу In P1 configuration, only two sections loft can be created.
8 Copyright DASSAULT SYSTEMES Когда стоит использовать прямые (Loft) и обратные (Removed Loft) тела по набору кривых? Позитивные или негативные тела по набору кривых используются в нескольких случаях: При создании комплексных твердых тел При создании переходной геометрии между двумя твердыми телами Функция Removed Loft используется для вычитания сложной поверхности из существующего твердого тела
9 Copyright DASSAULT SYSTEMES Создание тела по набору кривых: Направляющие кривые Выберете иконку тела по набору кривых (Loft) Выберете опцию направляющих Guide в диалоговом окне Укажите сечения, через которые пройдет тело. Обратите внимание на правильность порядка указания сечений Нажмите ОК Укажите направляющие Твердое тело прошло по выбранным сечениям и ограничено указанными направляющими
10 Copyright DASSAULT SYSTEMES Создание тела по набору кривых: Ориентирующая кривая Нажмите кнопку ориентирующей кривой Spine Укажите сечения, через которые пройдет тело. Обратите внимание на правильность порядка указания сечений Выберете иконку тела по набору кривых (Loft) Нажмите ОК От первого до последнего сечения тело построено вытягиванием вдоль ориентирующей кривой Укажите ориентирующую кривую
11 Copyright DASSAULT SYSTEMES Создание тела по набору кривых: Замыкающие точки и ориентация Замыкающая точка сечения Ориентация сечения Для изменения замыкающей точки сечения просто укажите другую точку на сечении Выбирая следующее сечение, может случиться, что его ориентация не совпадает с предыдущим. Для изменения щелкните на стрелке ориентации.
12 Copyright DASSAULT SYSTEMES Создание тела по набору кривых: Касательные поверхности Укажите первое сечение Укажите последнее сечение Укажите промежуточное сечение Подтвердите выбор Выберете поверхность, смежную последнему сечению Выберете поверхность, смежную первому сечению Результат Результат по тем же сечениям, но без условия касательности к смежным поверхностям
13 Copyright DASSAULT SYSTEMES Обратные тела по набору кривых (Removed Lofts) Рассмотрим способы создания негативных твердых тел по набору кривых Создание обратных тел по набору кривых
14 Copyright DASSAULT SYSTEMES Что такое обратное тело по набору кривых (Removed Loft)? Removed Loft – вычитает материал из существующего твердого тела за счет протягивания сечений вдоль направляющих или ориентирующих кривых
15 Copyright DASSAULT SYSTEMES Выберете иконку негативного тела по набору кривых (Removed Loft) Обратное тело по набору кривых Нажмите ОК Укажите сечения, через которые пройдет тело. Обратите внимание на правильность порядка указания сечений
16 Copyright DASSAULT SYSTEMES Создание негативного тела по набору кривых: Замыкающие точки и ориентация Ориентация сечения Замыкающая точка сечения Для изменения замыкающей точки сечения просто укажите другую точку на сечении Выбирая следующее сечение, может случиться, что его ориентация не совпадает с предыдущим. Для изменения щелкните на стрелке ориентации.
17 Copyright DASSAULT SYSTEMES Создание негативного тела по набору кривых: Касательные поверхности Укажите первое сечение Выберете поверхность, смежную первому сечению Укажите промежуточное сечение Укажите последнее сечение Выберете поверхность, смежную последнему сечению Подтвердите выбор Результат Результат по тем же сечениям, но без условия касательности к смежным поверхностям
18 Copyright DASSAULT SYSTEMES Сопряжение (Coupling) Рассмотрим применение опции Coupling при создании твердых тел по набору кривых Coupling при создании твердых тел по набору кривых
19 Copyright DASSAULT SYSTEMES Что такое сопряжение при создании тела по набору кривых? Опция сопряжения при использовании функций Loft и Removed Loft необходима для расчета детали, используя: Общий периметр сечений(ratio) Сечения между вершинами с прерывающейся кривизной Сечения между вершинами с прерывающейся касательной Вершины,с прерывающейся кривизной или касательной Вершины,с прерывающейся кривизной
20 Copyright DASSAULT SYSTEMES Сопряжение при создании тела по набору кривых Выберете иконку тела по набору кривых (Loft), укажите и сориентируйте сечения Выберете опцию сопряжения в диалоговом окне Выберете желаемый тип сопряжения в поле Нажмите ОК Опция сопряжения Coupling использует общую длину сечения, расстояние между вершинами, между точками сечений с непрерывной кривизной или касательной.
21 Copyright DASSAULT SYSTEMES Сопряжение при создании тела по набору кривых:по проценту (Ratio) Сопряжения в функциях Loft и Removed Loft использующие общую длину сечения(Ratio) Выберете иконку тела по набору кривых (Loft), укажите и сориентируйте сечения Выберете опцию сопряжения в диалоговом окне Выберете Ratioв поле сопряжений Нажмите ОК Результирующее тело построено по указанным сечениям. Разногласия между сечениями компенсируются сопряжением по общей длине Ratio Результат
22 Copyright DASSAULT SYSTEMES Сопряжение при создании тела по набору кривых:Тангенциально(Tangency) Выберете иконку тела по набору кривых (Loft), укажите и сориентируйте сечения Сопряжения в функциях Loft и Removed Loft использующие точки сечений с прерывающейся касательной Выберете опцию сопряжения в диалоговом окне Выберете Tangency Discontinuitiesв поле сопряжений Нажмите ОК Результат Результирующее тело построено по указанным сечениям. Сечения разбиваются точками с прерывающейся касательной
23 Copyright DASSAULT SYSTEMES Выберете опцию сопряжения в диалоговом окне Выберете Curvature Discontinuitiesв поле сопряжений Нажмите ОК Выберете иконку тела по набору кривых (Loft), укажите и сориентируйте сечения Результат Сопряжение при создании тела по набору кривых:Тангенциально(Tangency then Curvature) Сопряжения в функциях Loft и Removed Loft использующие точки сечений с прерывающейся кривизной Результирующее тело построено по указанным сечениям. Сечения разбиваются точками с прерывающейся кривизной
24 Copyright DASSAULT SYSTEMES Выберете опцию сопряжения в диалоговом окне Выберете Verticesв поле сопряжений Нажмите ОК Выберете иконку тела по набору кривых (Loft), укажите и сориентируйте сечения Результат Сопряжение при создании тела по набору кривых:По вершинам(Vertices) Сопряжения в функциях Loft и Removed Loft использующие вершины сечений Результирующее тело построено по указанным сечениям. Сечения разбиваются вершинами входящих отрезков
25 Copyright DASSAULT SYSTEMES Сопряжение при создании тела по набору кривых:Точки разрыва В CATIA имеется ряд особых точек, с помощью которых возможно разделять сечения при использовании опций сопряжения Рассмотрим различные типы прерывания гладкости на примере эскиза, показанного ниже: Эти две точки имеют разрыв кривизны и касательной и одновременно являются вершинами Две дуги Сегменты Эти две точки имеют разрыв кривизны и одновременно являются вершинами В этой вершине сохраняется гладкое сопряжение как касательной, так и кривизны
26 Copyright DASSAULT SYSTEMES Появится: Выберете иконку тела по набору кривых (Loft), укажите и сориентируйте сечения и направляющие Если сечения имеют разное количество вершин, возможно назначить их сопряжение вручную при определении замыкающих точек сечений Loft:Сопряжения вручную(1/2) В опции Coupling выберете Ratio Двойной щелчок на поле Coupling
27 Copyright DASSAULT SYSTEMES Loft:Сопряжения вручную(2/2) Если сечения имеют разное количество вершин, возможно назначить их сопряжение вручную при определении замыкающих точек сечений Для каждого сечения назначьте вершины, нажатием ОК завершите определение сопряжений. Если поставить отметку в окошке под Coupling, можно визуализировать кривые сопряжений. Порядок указания вершин должен совпадать с порядком указания сечений Нажмите ОК для завершения операции Замечание: Подобные опции могут использоваться и в негативном теле Removed Loft Результат: Замечание: Для изменения формы полученного тела, следует переопределить сопряжения: выберете первое сопряжение нажмите Add, далее как ранее
28 Copyright DASSAULT SYSTEMES Loft:Переопределение границ(1/3) Замечание: Подобные опции могут использоваться и в негативном теле Removed Loft Если окошко ограничения отмечено, тело всегда ограничено начальным и конечным сечениями в независимости от того продолжаются ли за ними направляющие или ориентирующие кривые По умолчанию тело по набору кривых всегда ограничивается первым и последним сечениями. Имеется возможность ограничить тело также длиной направляющих или ориентирующих кривых
29 Copyright DASSAULT SYSTEMES Loft:Переопределение границ(2/3) Замечание: Подобные опции могут использоваться и в негативном теле Removed Loft По умолчанию тело по набору кривых всегда ограничивается первым и последним сечениями. Имеется возможность ограничить тело также длиной направляющих или ориентирующих кривых Если окошко ограничения не отмечено и в построении используется ориентирующая кривая, тело будет ограничено началом и концом этой кривой
30 Copyright DASSAULT SYSTEMES Loft:Переопределение границ(3/3) По умолчанию тело по набору кривых всегда ограничивается первым и последним сечениями. Имеется возможность ограничить тело также длиной направляющих или ориентирующих кривых Если окошко ограничения не отмечено и в построении используется направляющие кривые, тело будет ограничено началом и концом этих кривых Замечание: Подобные опции могут использоваться и в негативном теле Removed Loft
31 Copyright DASSAULT SYSTEMES Изменение замыкающих точек (Closing points) Рассмотрим возможности изменения замыкающих точек сечений при создании твердых тел по набору кривых Изменение замыкающих точек
32 Copyright DASSAULT SYSTEMES Зачем менять замыкающие точки при создании тела по набору кривых? При выборе сечений для создания позитивного или негативного тела по набору кривых, имеется возможность назначить замыкающие точки в любом месте сечения
33 Copyright DASSAULT SYSTEMES Изменение замыкающих точек при создании тела по набору кривых (1/6) Выберете иконку тела по набору кривых (Loft), укажите первое сечение Укажите второе сечение Укажите третье сечение
34 Copyright DASSAULT SYSTEMES Изменение замыкающих точек при создании тела по набору кривых (2/6) Укажите замы- кающую точку Нажмите на надпись второго сечения Section2 Нажмите на надпись третьего сечения Section3 Укажите замыкающую точку Нажмите на стрелки второго и третьего сечений
35 Copyright DASSAULT SYSTEMES Изменение замыкающих точек при создании тела по набору кривых (3/6) Убедитесь, что в сопряжении указано Ratio, затем нажмите Apply в диалоговом окне Так как замыкающая точка в сечении 1 назначена по умолчанию и не соответствует точкам других сечений, тело получилось перекрученным
36 Copyright DASSAULT SYSTEMES Изменение замыкающих точек при создании тела по набору кривых (4/6) Для создания точки на кривой появляется новое диалоговое окно Перед подтверждением точка выделится синим цветом Для создания замыкающей точки в сечении 1 нажмите правой кнопкой на Section1
37 Copyright DASSAULT SYSTEMES Изменение замыкающих точек при создании тела по набору кривых (5/6) Выберете Distance on Curve Выберете опциюEuclidean Введите длину 100 мм Нажмите ОК
38 Copyright DASSAULT SYSTEMES Изменение замыкающих точек при создании тела по набору кривых (6/6) Выберете Distance on Curve Выберете опцию сопряжения в диалоговом окне Результат: Нажмите ОК Выберете Verticesв поле сопряжений
39 Copyright DASSAULT SYSTEMES Создание тела между поверхностями Выберите
40 Copyright DASSAULT SYSTEMES Точки 2 1 3
41 Copyright DASSAULT SYSTEMES Линии The created line appears under Open_Body
42 Copyright DASSAULT SYSTEMES Плоскости The created plane appears under Open_Body
43 Copyright DASSAULT SYSTEMES Создание пространственной кривой 1 You can create points according to their coordinates by using the Points tool in the Reference Element tool bar 2 Create the 3D curve by using the Curve in Space tool in the Free-Style workbench This curve can now be used to extrude a rib or create a slot
44 Copyright DASSAULT SYSTEMES Уклоны Advanced Drafts
45 Copyright DASSAULT SYSTEMES Advanced Draft
46 Copyright DASSAULT SYSTEMES What is the Advanced Draft Feature ? (3/5) The 1 st side tab is used to define the characteristics of the draft angle for the selected faces. If you decide to draft both sides, you have to define the draft angle characteristics for the second side using the 2 nd side tab. When drafting both sides with reflect lines, you define whether the draft angles are independent or not To define the Faces to be drafted To define the neutral element To define the pulling direction To define the draft angle value To define if the angles are the same or not when drafting both sides
47 Copyright DASSAULT SYSTEMES What is the Advanced Draft Feature ? (4/5) To define the Parting Element, you have to use the parting tab. The parting element can be a plane, a surface or a face To define the parting element
48 Copyright DASSAULT SYSTEMES What is the Advanced Draft Feature ? (5/5) When you decide to draft both sides with independent angles, you have to define the second side characteristics Neutral element To define the pulling direction To define the draft angle value To define if the angles are the same or not when drafting both sides
49 Copyright DASSAULT SYSTEMES Advanced Draft Angle: Draft Both Sides (1/9) Select the Advanced Draft icon 1 You are going to see how to draft both sides using the Advanced Draft icon Activate these two buttons 2
50 Copyright DASSAULT SYSTEMES Advanced Draft Angle: Draft Both Sides (2/9) Select this face as the object to be drafted 3
51 Copyright DASSAULT SYSTEMES Advanced Draft Angle: Draft Both Sides (3/9) Select the No Selection option from the Neutral Element combo, then select the indicated plane 4
52 Copyright DASSAULT SYSTEMES Advanced Draft Angle: Draft Both Sides (4/9) Enter 21 in the angle field 5 Select the parting tab 6
53 Copyright DASSAULT SYSTEMES Advanced Draft Angle: Draft Both Sides (5/9) Select the Parting Element button 7 Select the Parting Element field 8
54 Copyright DASSAULT SYSTEMES Advanced Draft Angle: Draft Both Sides (6/9) Select the indicated plane 9 Select the 2 nd side tab 10
55 Copyright DASSAULT SYSTEMES Advanced Draft Angle: Draft Both Sides (7/9) Select the No Selection option from the Neutral Element combo, then select the indicated plane 11
56 Copyright DASSAULT SYSTEMES Advanced Draft Angle: Draft Both Sides (8/9) Enter 45 in the angle field 12 Select Preview 13
57 Copyright DASSAULT SYSTEMES Advanced Draft Angle: Draft Both Sides (9/9) Select OK in the dialog box 14 You will see You get:
58 Copyright DASSAULT SYSTEMES Толщина (Thickness) 1 Multi-select the faces to be thickened 2 Modify the thickness definition of the material to add in the dialog box 3 A standard use of thickness is when material has to be added or removed before machining a part. Thickness captures the design intent and allows rapid change Select Thickness icon Select the Other thickness faces field then select another face 4 Enter –5 in the Other thickness field then select OK 5 You get: –5mm
59 Copyright DASSAULT SYSTEMES Additional Information (1/3) In some cases, when you want to create an Offset, an error message appears informing you that the Body cant built properly. After closing the window, another message appears proposing you to Ignore the Faces causing trouble. If you accept, the Thickness is created and the Face causing trouble is removed. For example, here we want to offset the selected Face but it is not possible. The Face causing trouble is the Radius Fillet. We accept to ignore the Fillet, thus the Thickened Body becomes : Ignoring Faces
60 Copyright DASSAULT SYSTEMES Additional Information (2/3) If we edit the Thickness from the specification tree, the Ignored Faces are previewed : The option Reset Ignored Faces appears in the Thickness Definition Dialog box. After selecting this option, the Ignored Faces are reinitialized and the indication Ignored Face in the geometry is removed.
61 Copyright DASSAULT SYSTEMES Additional Information (3/3) In some cases, you have to use the Extract command in order to add thickness. With this command, you can generate separate Elements from initial geometry, without deleting geometry. This command is available after clicking a Dialog box prompting you to deactivate the Thickness feature and Extract the geometry. Once this operation has been done, a node Extracted Geometry is displayed in the tree. If the Generative Shape Design Workbench is installed, the geometry resulting from the Extract operation is associative. Extracting Geometry
62 Copyright DASSAULT SYSTEMES Translation 4 1 Select OK Select the Translation icon Enter the distance or drag the icon, then select OK You can also define the direction using the contextual menu on the Direction field 3
63 Copyright DASSAULT SYSTEMES Rotation Select the Rotation icon Select an edge for rotation axis... …and enter the rotation angle or drag the icon 1 2 You can also define the axis using the contextual menu on the Axis field Select OK 3
64 Copyright DASSAULT SYSTEMES Symmetry Select OK Select the plane defining the symmetry Select the Symmetry icon Instead of a plane, you can use a Point as the Reference element Instead of a plane, you can use a Segment as the Reference element You can also define the Reference using the contextual menu on the Reference field
65 Copyright DASSAULT SYSTEMES What is a 3D Constraint ? A 3D Constraint is the same as any other constraint only that it is applied in the 3D model itself. Basically you will note that some are reference type constraints and others are regular constraints. Creation is the same as in the Sketcher, so we will concentrate on their usage here Normally, 3D constraints are modifiable and can be linked and driven as others are in the Sketcher They are references because there are other constraints that are constraining the geometry Reference constraints are shown in parenthesis and cannot be modified
66 Copyright DASSAULT SYSTEMES When to Use 3D Constraints ? They can be used whenever you have 3D geometry that you want to link to some type of 3D datum plane or surface You may also find it useful when you are using Copy and Paste to locate the pasted piece of Geometry from where you wish They are also useful when you need to drive the location of a piece of geometry created earlier in the design from a piece of geometry created later in the model. Thus this will limit some of the need to re-ordering of the part
67 Copyright DASSAULT SYSTEMES Creating 3D Constraints 1 Select the Constraint icon and create a constraint between the left side surface and the hole on the left side of the part 2 Note: The first dimension created was not a reference dimension. No Parenthesis were on the value. The second dimension was a reference dimension because the hole is located with the sketch for the hole from the same or the right side edge Now repeat the process from the same side to the hole on the left side of the part
68 Copyright DASSAULT SYSTEMES Using 3D Constraints 1 You will drive the location of Pocket.1 from Hole.2 created after it in the tree 2 Modify the constraint indicated in red to 25mm and the Pocket.1 is now driven from the Hole.2 location 3 Create the two constraints shown below from the center line of Hole.2 to the edges of the Pocket.1 Note: This capability will allow you to drive location of features in the tree from features created after them without having to do re-location of features in the tree.
69 Copyright DASSAULT SYSTEMES Local Axis : Creation It is possible to create a local axis in order to define local coordinates. For example, it is, sometime, easier to define point coordinates with respect to a local axis rather than to the absolute coordinates system Select the Axis System icon Select the local axis origin point (2) Select the OX direction Select the OY direction You get : (3) (4) Select OK in the dialog box (5)
70 Copyright DASSAULT SYSTEMES Local Axis : Use It is possible to create a local axis in order to define local coordinates. For example, it is, sometime, easier to define a point coordinates with respect to a local axis rather than to the absolute coordinates system Set the axis system As the Current one with the contextual menu You get : Using the Point function (Coordinates options), create a point with X=0, Y=0 and Z=100 (1) 1 2
71 Copyright DASSAULT SYSTEMES Local Axis-System Setting In the Options dialog box, select Mechanical Design -> Part Design then the Part Document tab 2 Select the Create an Axis System when creating a new part option 3 Select OK 4
72 Copyright DASSAULT SYSTEMES Local Axis-System Setting Double click on Part in the dialog box 5 Select the File -> New command 6 The local axis is automatically created:
73 Copyright DASSAULT SYSTEMES Общая информация Local Axis dialog box To expand the dialog box To shrink the dialog box To define the axis system origin To define the OX axis To define the OY axis To define the OZ axis To reverse the OZ axis To reverse the OY axis To reverse the OX axis
74 Copyright DASSAULT SYSTEMES Texts with Leader Select the Text with Leader icon 1 Select the position of the leader on the part 2 Enter the text in the dialog box then select OK 3 Place the text and the leader by dragging the arrow or the square points 4 You get:
75 Copyright DASSAULT SYSTEMES Flag Note with Leader You will learn how to add hyperlinks to your document and then use them to jump to a variety of locations
76 Copyright DASSAULT SYSTEMES Flag Notes with Leader (1/2) Enter Part Process in the Name field Select the Flag Note with Leader icon 1 Select the position of the leader on the part 2 3
77 Copyright DASSAULT SYSTEMES Flag Notes with Leader (2/2) You get: Place the text and the leader by dragging the arrow or the square points 5 Select the Browse button then select the file you want to link then select OK 4
78 Copyright DASSAULT SYSTEMES Using Flag Notes with Leader Select the Go to button in the dialog box Double click on the flag 1 Select the Link in the dialog box 2 3 The linked file is now started
79 Copyright DASSAULT SYSTEMES Analyzing Threads and Taps You will learn how to display and filter out information about threads and taps contained in a part
80 Copyright DASSAULT SYSTEMES What is Thread and Tap Analysis ? When a part has been created with threads and taps, CATIA does not physically display these features. There is a way to quickly know all the information about threads and taps by using the Thread and Tap Analysis icon You can display threads or taps or both You can display the threads and taps numerical values You can display threads or/and taps of a given diameter value
81 Copyright DASSAULT SYSTEMES Analyzing Threads and Taps (1/2) You can display and filter out information about threads and taps contained in a Part Select the Tap – Thread Analysis icon Expand the dialog box using the More button 1 2 Select the criteria that will define the types of thread / tap that will be displayed 3 To show the threads or taps geometry To show the threads or taps values To show diameters with a given value To show taps To show threads
82 Copyright DASSAULT SYSTEMES Analyzing Threads and Taps (2/2) Select Apply in the dialog box You get: 4
83 Copyright DASSAULT SYSTEMES Draft Analysis You will learn how to analyze the draft angle on the surface of a part
84 Copyright DASSAULT SYSTEMES What is Draft Analysis ? The Draft Analysis command allows you to analyze the draft angle on the surface of a part. You will be able to detect if the part you drafted will be easily removed from the associated mold This type of analysis is performed based on color ranges identifying zones on the analyzed element where the deviation from the draft direction, represented by the normal to the surface at a given point, corresponds to specified values The cursor manipulation for colors is limited to -20 and 20 but the analysis is performed between -90 and 90 degrees. To get a result, the view mode must be turned to Material display
85 Copyright DASSAULT SYSTEMES Draft Analysis (1/2) The Draft Analysis capability allows you to analyze the draft angle on the surface of a part. You will be able to detect if the part you drafted will be easily removed from the associated mold Select the Draft Analysis icon 1 Drag the red point of the Compass and drag it onto a face perpendicular to the direction of extraction 2
86 Copyright DASSAULT SYSTEMES Draft Analysis (2/2) Select the Invert analysis direction in the dialog box 2 You get: Everything in green is correct Everything in red is incorrect You have to take care of the light blue faces but it might correct You have to take care of the dark blue faces because it is certainly incorrect
87 Copyright DASSAULT SYSTEMES Additional Information Draft Analysis dialog box You can customize these colors by double clicking To smooth the analysis To fix a direction of extraction, uncheck the Locked direction option, and select a direction (a line, or a plane which normal is used), or use the compass manipulators, when available If you move the pointer over the green arrow (Normal), the inverted normal is displayed in dotted line Circles are displayed indicating the plane tangent to the surface at this point
88 Copyright DASSAULT SYSTEMES What are Mean Dimensions? When creating dimensional constraints, you can define a tolerance. Using the Mean Dimensions icon you can compute the mean dimensions and the part will be updated. This can be useful for a part to be machined Dimension with a Tolerance Mean dimension
89 Copyright DASSAULT SYSTEMES Mean Dimensions (1/4) 1 2 Double click on the indicated dimension We are going to add tolerances on dimensions which have been created in the sketch of the shaft. Double click on Sketch.1
90 Copyright DASSAULT SYSTEMES Mean Dimensions (2/4) 3 4 In the appearing dialog box, enter 0.2 in the Maximum tolerance filed and enter 0.1 in the Minimum tolerance field then select OK Using the contextual menu on the Value field, select the Add Tolerance command 5 The tolerance is created. Select Ok in the Constraint Definition dialog box then Exit the sketcher Dimension with a tolerance
91 Copyright DASSAULT SYSTEMES Mean Dimensions (3/4) 6 7 Select OK To compute the mean dimensions, select the Mean Dimension icon 8 Select the Update All icon If you look at the dimensions in Sketch.1, you will see that they are changed to their means. The part is also updated
92 Copyright DASSAULT SYSTEMES Mean Dimensions (4/4) 9 10 Select OK To come back to nominal dimensions, select the Mean Dimension icon 11 Select OK 12 Select the Update All icon If you look at the dimensions in Sketch.1, you will see that they are changed to their nominal size. The part is also updated
93 Copyright DASSAULT SYSTEMES What is Scanning a Part ? Scanning a part means to replay the construction history of a part and isolate temporarily any feature to work locally
94 Copyright DASSAULT SYSTEMES What are Parents-Children Relationships ? Parents-children relationships provides an accurate view of genealogical links between elements. We recommend you to use it before deleting elements parents children Pad 1 Pad 2 Pad 3
95 Copyright DASSAULT SYSTEMES Parents-Children Relationship Pad 1 2 Select the Parent-Children option 3 Activate the contextual menu on the desired feature (here, Pad.1) 1 The graph allows you to show all parents / children (MB3) Double-click a component to show/hide parents or children parents children
96 Copyright DASSAULT SYSTEMES Parents-Children (Edition) (1/2) Select the Parent/Children option in the contextual menu Parent Children allows you to edit features 1 2 You get: Note : It is possible to see if a component is a Published Element or not, by selecting the Show Parents and Children Contextual option on this component.
97 Copyright DASSAULT SYSTEMES Parents-Children (Edition) (2/2) Select the Edit command from the fillet contextual menu Modify the fillet radius then select OK 3 4 You get: 5
98 Copyright DASSAULT SYSTEMES Cut/Copy and Paste (Drag and Drop) One way you can copy the limits of the circular pad to apply to the rectangular pad is to work within the Part tree and use the 3rd. mouse button to copy Pad.2 and Paste onto Sketch.3 Another way for the fillet - Keeping the CTRL key pressed, drag with the 1st. mouse button to one of the base edges of the rectangular pad You can copy the draft by using another way - 3rd. mouse button to copy Draft.1 from the tree then select a vertical face on the rectangular pad and 3rd. mouse button to paste 2 3 1
99 Copyright DASSAULT SYSTEMES When to Use Isolate and Break ? Isolate is used when 3D geometry is projected into a sketch in order to be modified and used as part of the sketchs profile. Isolate duplicates the element since the original element cannot be changed because other geometry depends on it Break is used to divide an isolated element into two parts at a specified point (usually to use one side of this element in the sketch)
100 Copyright DASSAULT SYSTEMES Isolate, Break (1/3) Using the Trim and Break icon in the sketcher, modify the sketch as follows, then exit the sketcher Starting with the geometry below, we want to add a pad 2 1 Lines Added pad Diameter 100 Pad Intersection between the pad and the sketch plane Diameter 50 Create a pad with an length of 20 3
101 Copyright DASSAULT SYSTEMES Isolate, Break (2/3) Edit the Sketch of the first pad then change the circle diameter to 50 Select the Undo icon (may be several times) in order to come back to diameter 100 Exit the sketcher (Sketch.1) then, if necessary, Update the part. You will get: Edit Sketch.2, then place the cursor on the yellow line then select Isolate from the contextual menu 7
102 Copyright DASSAULT SYSTEMES Isolate, Break (3/3) Create two Coincidence between the isolated arcs and the cylinder then exit the sketcher Exit the sketcher then, if necessary, Update the part. You will get: Edit the Sketch (Sketch.1) of the first pad then change the circle diameter to
103 Copyright DASSAULT SYSTEMES Создание нового тела в открытом файле A body is added in the tree In order to insert a Body, select the Insert -> Body command 2 1 You can work in the PartBody or in Body.2. Top Switch from one Body to another, select the Define in Work Object option in the contextual menu of the desired body
104 Copyright DASSAULT SYSTEMES Булевы операции Assembling/Adding : If Body2 is Assembled or Added to Body1, the operation between the bodies is a Union. The only difference between the two is that Assemble will respect the nature of features. If Body2 contains as its first node a Pocket feature (permissible), Assemble will see it as a Pocket and remove material from Body1. In this case, if Add is used, the Pocket will be seen by Body1 as a Pad Intersecting : результат – общий объём 2-х тел Removing : вычитание Body1 минус Body2 Union Trim : The Union Trim is basically a Union with an option to remove or keep one side or the other. In the picture on the right, the purple face is selected to remove the right side and the blue face is selected to keep only the top side. For the Union Trim to work, the geometry must have sides that are clearly defined Remove Lump : All the above options work between two bodies. The Remove Lump works on geometry within a specific Body. If a single Body has material that is completely disconnected, each piece of disconnected material is defined as a Lump. The user can delete any Lump as a single entity even if the Lump is a combination of numerous features
105 Copyright DASSAULT SYSTEMES Assemble With the cursor on Body.2, select Assemble from the contextual menu (MB3) We want to assemble Body.2 with PartBody 2 1 You get: Body.2 contains a groove Because Body.2 contains a groove which is a feature that removes material, the result of the assemble operation is also removing material Select OK in the Dialog box 3
106 Copyright DASSAULT SYSTEMES Add With the cursor on Body.2, select Add in the contextual menu (MB3) We want to add Body.2 with PartBody 2 1 You get: Body.2 contains a groove Body.2 contains a single groove, so it appears as a solid (even if it normally removes material). When you Add a Body, CATIA keeps the feature like it appears before the addition. Select OK in the Dialog box 3
107 Copyright DASSAULT SYSTEMES Remove With the cursor on Body.2, select Remove in the contextual menu (MB3) We want to remove Body.2 from PartBody 2 1 Select OK in the Dialog box 3 You get:
108 Copyright DASSAULT SYSTEMES Intersect We want to intersect Body.2 with PartBody 1 With the cursor on Body.2, select Intersect from the contextual menu (MB3) 2 Select OK in the Dialog box 3 You get:
109 Copyright DASSAULT SYSTEMES Union Trimming Bodies We want to do a Union Trim of Body.2 with PartBody 1 With the cursor on Body.2, select Union Trim in the contextual menu (MB3) 2 Select the Face to remove then the face to keep (Activate the corresponding field before in the dialog box) 3 You get: Select OK 4
110 Copyright DASSAULT SYSTEMES Removing Lumps With the cursor on PartBody, select Remove Lump in the contextual menu (MB3) 1 Select the Faces to remove field in the dialog box 2 Select the two following faces belonging to the lumps to be removed 3
111 Copyright DASSAULT SYSTEMES Assembling a Set of Bodies (1/3) Assembling a set of bodies (Multi selected using the Ctrl key) is possible Using the Ctrl key, select the three following bodies to be assembled 1
112 Copyright DASSAULT SYSTEMES Assembling a Set of Bodies (2/3) With the cursor placed on the last body, select the Assemble option in the contextual menu 2
113 Copyright DASSAULT SYSTEMES Assembling a Set of Bodies (3/3) Select OK in the dialog box 3 You get:
114 Copyright DASSAULT SYSTEMES What is Replacing a Body? You can replace a body used in an operation by another one
115 Copyright DASSAULT SYSTEMES Replacing a Body (1/3) Select the Replace command from Body.3 contextual menu 1 Body to be replaced Replacing body Select Body.4 2
116 Copyright DASSAULT SYSTEMES Replacing a Body (2/3) Select the following line in the dialog box 3 Select the following face. This face is the face that will be removed during the Union Trim operation 4 Select OK 5
117 Copyright DASSAULT SYSTEMES Replacing a Body (3/3) If necessary, update the part by selecting the Update All icon 6 You get:
118 Copyright DASSAULT SYSTEMES Changing the Boolean Type (1/4) The initial part is composed of three bodies. Assemble Body.1 to Part Body. 1 Remove Body.2 from Assemble.1. You obtain Remove.1. 2
119 Copyright DASSAULT SYSTEMES Changing the Boolean Type (2/4) Click with the right button mouse on Remove.1. In the contextual menu, select Remove.1 object 3 Choose now the new operation. For example, click on Change To Assemble. 4
120 Copyright DASSAULT SYSTEMES Changing the Boolean Type (3/4) You obtain : 5 Change now Assemble.2 to Union Trim. You obtain : 6
121 Copyright DASSAULT SYSTEMES Changing the Boolean Type (4/4) You can edit Trim.1. For instance, select the cylinder's top face as the face to keep. You obtain : 7
122 Copyright DASSAULT SYSTEMES Establishing Multi-Model Links (3/3) Now, in Sketch.1 of part2, create a diameter constraint of 50 then exit the sketcher Part1 becomes: 7 With Part1 active, select the Update All icon 8 6 You get:
123 Copyright DASSAULT SYSTEMES Sketch Selection with Multi-Document Links Select AsResultWithLink in the dialog box 5 6 Expand Sketch.1 in order to see what has been copied (by selecting +) Вы можете скопировать sketch в другой документ с сохранением связи.
124 Copyright DASSAULT SYSTEMES Общая информация As specified in Part document: Сохраняется история построения, но отсутствуют связи AsResultWithLink: Вставляется результат без истории построения, но сохраняется связь Опции вставки:
125 Copyright DASSAULT SYSTEMES Масштабирование You can also resize a body in relation to a face or plane by selecting it instead of a reference point. The body will scale with it. You will obtain an affinity Select the reference point Select the Scaling icon Modify the scaling ratio then select OK You get:
Еще похожие презентации в нашем архиве:
© 2024 MyShared Inc.
All rights reserved.