Мы предполагаем, что вам понравилась эта презентация. Чтобы скачать ее, порекомендуйте, пожалуйста, эту презентацию своим друзьям в любой соц. сети. Кнопочки находятся чуть ниже. Спасибо.
Идет загрузка презентации. Пожалуйста, подождите
Презентация была опубликована
3 года назад
© 2009 Avaya Inc. All rights reserved.1 Chapter Nine, Voic Pro in SCN Module One – Meshed Network with IPO
© 2009 Avaya Inc. All rights reserved.2 Small Community Network (SCN) Overview When connecting IP Offices together over IP or Packet based networks, Small Community Networking enhances feature transparency. These networks can support up to a maximum of 1000 users across 32 sites. The following additional features are available:
© 2009 Avaya Inc. All rights reserved.3 SCN Requirements For Small Community Networks VCM modules are required in all systems being connected. The IP lines may be configured in a star or a meshed configuration. Each IP Office system broadcasts UDP messages on Port SCN is supported between IP Office systems with the same major software level or one level of difference in major software level. For example between 4.2 and 4.1 (same major level) and between 5.0 and 4.2 (one major level of difference). If larger networks are required QSIG can be used to link multiple Small Community Networks together. Functionality between the communities is governed by the QSIG feature set.
© 2009 Avaya Inc. All rights reserved.4 SCN Requirements - continued QSIG, H.323 and SCN capabilities are not enabled by default in the IP500 and IP500v2. On IP500 and IP500v2 systems Small Community Networking requires one or more additional licenses. – An additional license is required to enable this functionality with 4 simultaneous networking channels. – Additional channels can then be licensed in increments of 4. – A Voice Networking license is required to enable TDM QSIG, even though there is no limit to the number of TDM QSIG calls that can be made or received once licensed.
© 2009 Avaya Inc. All rights reserved.5 Supported SCN Configuration: Star / Serial The following are examples of star and serial layouts. These are the only types of layouts supported for Small Community Networks containing any pre-IP Office Release 5 systems. The IP network supporting the SCN may be meshed, but the IP Office configuration must use a star, serial or a star / serial combination configuration.
© 2009 Avaya Inc. All rights reserved.6 Supported SCN Configuration: Meshed The use of 'mesh' layout connections is supported for a Small Community Network beginning with IP Office Release 5. A mesh layout contains H.323 SCN Line routes between two or more IP Office control units. Mesh, star and serial layouts can be combined.
© 2009 Avaya Inc. All rights reserved.7 Protocol Considerations When deploying IP Office in a meshed environment there are some common protocols that may deployed to support the IP Network supporting the SCN: Spanning Tree Protocol (STP): Layer 2 protocol that allows for network connection redundancy while preventing physical loops. Multiprotocol Label Switching (MPLS): is a highly scalable, protocol agnostic, data-carrying mechanism where data packets are assigned labels and packet-forwarding decisions are made solely on the contents of this label. MPLS is often referred to as a "Layer 2.5" protocol. Open Shortest Path First (OSPF): is a Layer 3 link-state routing protocol and is perhaps the most widely-used protocol in enterprise networks.
© 2009 Avaya Inc. All rights reserved.8 Routing Information Protocol (RIP) RIP is a simple method for automatic route sharing and updating within small networks. It allows alternate routes to be advertised when an existing route fails. IP Office systems can utilize RIP on LAN1, LAN2 and individual services with the following options: – Listen Only (Passive): Listen to RIP1 and RIP2 messages and update the routing table, do not advertise routes. – RIP1: Listen to RIP1 and RIP2 messages and advertises routes in a RIP1 sub-network broadcast. – RIP2 Broadcast (RIP1 Compatibility): Listen to RIP1 and RIP2 messages and advertise routes in a RIP2 sub-network broadcast. – RIP2 Multicast: Listen to RIP1 and RIP2 messages and advertise routes to the RIP2 multicast address ( ).
© 2009 Avaya Inc. All rights reserved.9 Network Address Translation (NAT) NAT is the process of modifying network address information in IP packet headers while in transit through a router for the purpose of remapping a given address space into another. NAT is useful as internally most networks use addresses that have been reserved for public use within networks but are not valid for routing across the internet and it allows multiple users to use the same address simultaneously (PNAT). IP Office can use NAT on the LAN1 and LAN2 (WAN) interfaces to support data services and lines / trunks: H323 Line, IP DECT Line, SIP Line and SES Line. The Static NAT table in the IP Office Firewall allows address translation between up to 64 selected internal and external IP address pairs.
© 2009 Avaya Inc. All rights reserved.10 Private Address Space The Internet Assigned Numbers Authority (IANA) has reserved the following three blocks of the IP address space for private internets: An enterprise that decides to use IP addresses as listed above can do so without any coordination with IANA or an Internet registry.
© 2009 Avaya Inc. All rights reserved.11 SCN Signaling Within an SCN the separate IP Office systems 'learn' each other's extension numbers and user names. IP Office SCN uses a signaling similar to RIP is order to update each other of there presence. This traffic can be seen in the IP Office System Monitor application as AVRIP packets. Each IP Office system listens for AVRIP traffic on port Each IP Office in the SCN transmits an update every 30 seconds. Additionally BLF updates are transmitted when applicable up to a maximum of every 0.5 seconds. Typically the volume is less than 1Kbps per IP Office system.
© 2009 Avaya Inc. All rights reserved.12 SCN Configuration Requirements To set up a small community network, the following are required: – H323 trunk(s) between the IP Office systems (H323 Line) On IP500 and IP500v2 systems, H323 trunks require the entry of IP500 Voice Networking licenses – Data routing between IP Office systems (IP Route) – The extension, user and group numbering on each system must be unique. – The user and group names on each system must be unique. – All systems should use the same set of telephony timers, especially the Default No Answer Time. – Avaya recommends that all names and numbers (line, services, etc) on the separate IP Office systems are unique.
© 2009 Avaya Inc. All rights reserved.13 Bandwidth Calculator
© 2009 Avaya Inc. All rights reserved.14 H323 Trunk Configuration
© 2009 Avaya Inc. All rights reserved.15 Three Site SCN Example The table below shows the H323 Trunk configuration options for a three site SCN with a meshed configuration.
© 2009 Avaya Inc. All rights reserved.16 IP Office SCN - Fallback IP Office Release 5 provides a number of features that allows IP Offices to provide fallback functions for each other. Each IP Office in the SCN can include one H323 line where the Supplementary Services is set to IP Office SCN – Fallback. Once a line is set to IP Office SCN - Fallback, the following options are available: – Backs up my IP Phones – Backs up my Hunt Groups – Backs up my Voic Fallback is only intended to provide basic call functionality if the IP Office is not visible within the SCN for a period of more than 3 minutes.
© 2009 Avaya Inc. All rights reserved.17 IP Route Settings When an IP Office needs to send data to IP addresses on a different subnet, for example another IP Office in a Small Community Network (SCN), the IP Route table is used by the IP Office to determine where data traffic should be forwarded. This is done by matching details of the destination IP address to IP Route entries and then using the Destination specified by the matching IP route. These are referred to as 'static routes'.
© 2009 Avaya Inc. All rights reserved.18 Three Site SCN Example The table below shows the IP Route configuration options for a three site SCN with a meshed configuration.
© 2006 Avaya Inc. All rights reserved. Network Small Community Network Network Small Community Network.
© 2005 Cisco Systems, Inc. All rights reserved. BGP v3.25-1 Customer-to-Provider Connectivity with BGP Connecting a Multihomed Customer to Multiple Service.
© 2006 Cisco Systems, Inc. All rights reserved. ICND v2.32-1 Extending Switched Networks with Virtual LANs Introducing VLAN Operations.
© 2006 Cisco Systems, Inc. All rights reserved. MPLS v2.25-1 MPLS VPN Implementation Configuring Small-Scale Routing Protocols Between PE and CE Routers.
© 2005 Cisco Systems, Inc. All rights reserved. BGP v3.23-1 Route Selection Using Policy Controls Applying Route-Maps as BGP Filters.
© 2009 Avaya Inc. All rights reserved.1 Chapter Three, VoiceMail Pro Advanced Functions Module Three – TAPI.
© 2009 Avaya Inc. All rights reserved.1 Chapter Nine, VoiceMail Pro in SCN Module Two – Centralized VoiceMail Pro.
© 2009 Avaya Inc. All rights reserved.1 Chapter Nine, VoiceMail Pro in SCN Module Four – Distributed VoiceMail Pro.
© 2006 Cisco Systems, Inc. All rights reserved. MPLS v2.24-1 MPLS VPN Technology Introducing the MPLS VPN Routing Model.
© 2005 Cisco Systems, Inc. All rights reserved. BGP v3.25-1 Customer-to-Provider Connectivity with BGP Understanding Customer-to-Provider Connectivity.
© 2009 Avaya Inc. All rights reserved.1 Chapter One, Getting Started Module Two – First Steps.
© 2009 Avaya Inc. All rights reserved.1 Chapter Two, VoiceMail Pro Components Module Two – Actions, Variables & Conditions.
© 2006 Cisco Systems, Inc. All rights reserved. BSCI v3.06-1 Implementing BGP Explaining BGP Concepts and Terminology.
Mobility Control and one-X Mobile. Mobility Control User Configuration Mobile Call Control requires PRI-U, BRI or SIP (RFC2833) trunks in the IP Office.
© 2009 Avaya Inc. All rights reserved.1 Chapter Nine, VoiceMail Pro in SCN Module Three – Backup VoiceMail Pro.
© 2005 Cisco Systems, Inc. All rights reserved. BGP v3.21-1 BGP Overview Understanding BGP Path Attributes.
© 2006 Cisco Systems, Inc. All rights reserved. CIPT1 v5.03-1 Deployment of Cisco Unified CallManager Release 5.0 Endpoints Configuring Cisco Unified CallManager.
© 2006 Cisco Systems, Inc. All rights reserved. MPLS v2.25-1 MPLS VPN Implementation Configuring VRF Tables.
© 2005 Cisco Systems, Inc. All rights reserved.INTRO v2.17-1 Connecting to Remote Networks Using Packet Switching in WANs.
© 2006 Cisco Systems, Inc. All rights reserved. BSCI v3.02-1 Configuring EIGRP Using EIGRP in an Enterprise Network.
Еще похожие презентации в нашем архиве:
© 2018 MyShared Inc. All rights reserved.