BALTECH shaft alignment systems. Shaft alignment systems BALTECH SA series BALTECH SA-4000 BALTECH SA-4100 BALTECH SA-4200 BALTECH SA-4300 BALTECH SA-Pro. - презентация

1 BALTECH shaft alignment systems

2 Shaft alignment systems BALTECH SA series BALTECH SA-4000 BALTECH SA-4100 BALTECH SA-4200 BALTECH SA-4300 BALTECH SA-Pro BALTECH FG-207 BALTECH-23458N Baltech FG – Feeler Gauges

3 – a universal leveling laser transmitter – a laser transmitter – a 2-axis receiver – a receiver with a laser 80 mm Laser geometry measurement system BALTECH LL («LaserLevel» series)

4 BALTECH has developed and manufacturers inexpensive, simple and efficient electronic and mechanical alignment systems BALTECH SA «ShaftAlignment» Series, that allow to perform horizontal and vertical shaft alignment. All our alignment systems allow to perform the alignment with two methods: Rim-Face Alignment method (radiaxial method) and Reversed-Rim alignment method (dial indicator method)

5 BALTECH SA-4000 is a tool kit for shaft alignment with dial indicators and without a unit for misalignment calculation. This is the inexpensive kit for horizontal and vertical shaft alignment. This tool kit doesn't include a measurement unit and is recommended for use by experienced specialists. The measurements are conducted with dial indicators. The received data is used to calculate the misalignment amount. If you want to extend your system up to BALTECH SA-4100, BALTECH SA-4200 or BALTECH SA-4300 you only need to purchase a measurement unit. The universal fixtures and rods are mounted on the shafts without clearances. To ensure proper alignment we recommend to use stainless steel shims BALTECH Functions: Horizontal shaft alignment; Vertical shaft alignment; Check and elimination of soft foot during alignment; Alignment method selection: radiaxial method or dial indicator method BALTECH SA-4000 Number of indicators (dial)2 Sensor typeDial indicator Measurement range Not less than 10 mm Measurement accuracy0,01 mm Maximum diameter of mating shafts (couplings): - with chains with magnets (options)Not limited Rod length320 mm

6 BALTECH SA-4100 The BALTECH SA-4100 shaft alignment system with dial indicators on the basis of a pocket computer is intended to perform shaft alignment of horizontal and vertical pumps and fans. The system has a tape with a liquid level for precise installation of the dial indicators. The device is low cost and high-performance. BALTECH SA-4100 has the pocket computer with a program for misalignment calculation. The program calculates the required movements of the electric motor front and rear feet based on three of four points. Functions: Shaft alignment of horizontal machines 9-0-3; Shaft alignment of vertical machines 9-0-3; Check and elimination of soft foot during the shaft alignment; Thermal growth compensation; Selection between the alignment methods: radiaxial method or dial indicator method; Built-in digital camera Number of indicators (dial)2 Sensor typeDial indicator Measurement range Not less than 10 mm Measurement accuracy0,01 mm Maximum diameter of mating shafts (couplings): - with chains600 - with magnets (options)Not limited Rod length320 mm Measurement unitPocket PC Operation temperature-15°C…+45°C

7 BALTECH SA-4200 Number of indicators (dial)2 Sensor type Electronic indicator Measurement range Not less than 12,5 mm Measurement accuracy0,01 mm Maximum diameter of mating shafts (couplings): with chains600 - with magnets (options)Not limited Rod length290 mm Measurement unitPocket PC Operation temperature-15°C…+45°C BALTECH SA-4200 is a system for alignment of electric motors with digital electronic indicators on the bases of a pocket computer. The system is designed to perform the shaft alignment of horizontal and vertical machines. Functions: Shaft alignment of horizontal machines 9-0-3; Shaft alignment of vertical machines 9-0-3; Check and elimination of soft foot during the shaft alignment; Thermal growth compensation; Selection between the alignment methods: radiaxial method or dial indicator method; Built-in digital camera

8 BALTECH SA-4300 Number of measurement channels2 Sensor typeDigital indicator Measurement range0-13 mm Measurement accuracy0,01 mm Maximum diameter of mating shafts (couplings): with chains600 - with magnets (options)Not limited Rod length290 mm Measurement unitElectronic unit DisplayColor LCD 3,5" Data transfer to PCUSB Operation temperature-15°C…+45°C Safety classIP-54 BALTECH SA-4300 is an electronic and mechanical alignment system with digital electronic indicators. This is a fully automated set for shaft alignment of horizontal and vertical machines. The digital indicators are connected directly to the electronic unit via cables. The electronic unit carries out automatic calculation of misalignment values in two planes. BALTECH SA-4300 allows to perform the machine alignment in real-time mode. The alignment report is stored in the device memory and can be transferred to the BALTECH Expert software. Functions: Horizontal shaft alignment 9-0-3; Vertical shaft alignment 9-0-3; Check and elimination of soft foot; Compensation of thermal growth ; Compensation of shaft floating on oil wedge ; Compensation of the rod deflection ; Alignment of machines with intermediate shafts ; On-line alignment quality control; Selection between the alignment methods: radiaxial method or dial indicator method; Alignment results are stored in the device memory ; Report transfer to PC

9 BALTECH-23458N - set of calibration shims for the shaft alignment

10 BALTECH DM (DM-SL-2) - self-adjusting chocking elements for the vertical machine movement

11 BALTECH FG - set of calibration gauges for the soft foot checking Set of standard and long gauges BALTECH FG Series Set 8 pcs. 0,05-0,5 mm Set 13 pcs. 0,05-1 mm Set 20 pcs. 0,05-1 mm Set 20 pcs. 0,1-2 mm L, mm BALTECH FG-81BALTECH FG-131BALTECH FG-201BALTECH FG BALTECH FG-82BALTECH FG-132BALTECH FG-202BALTECH FG BALTECH FG-83BALTECH FG-133BALTECH FG-203BALTECH FG BALTECH FG-84BALTECH FG-134BALTECH FG-204BALTECH FG BALTECH FG-85BALTECH FG-135BALTECH FG-205BALTECH FG BALTECH FG-86BALTECH FG-136BALTECH FG-206BALTECH FG (21шт)100 Set 6 pcs. 0,1-0,4 mm Set 7 pcs. 0,1-0,5 mm Set 10 pcs. 0,1-1,0 mm Set 11 pcs. 0,05-0,8 mm L, mm BALTECH FG-87BALTECH FG-137BALTECH FG-207BALTECH FG (21шт)75 The set of calibration gauges (gauge) is made of tampered stainless steel and brass. The measurement gauges BALTECH FG Series are intended to measure clearances in different fields, e.g. in motor-building, for adjustment of valve clearances, radial clearances in bearings and during alignment works (determination of half coupling gaps and «soft foot» type), etc. The set of gauges (gauge) are delivered in size 75, 100, 150, 200, 300, 500, 1000mm.

12 BALTECH SA-PRO BALTECH SA-PRO has been developed by BALTECH for specialists who already use BALTECH SA Series systems for alignment. Based on our experience we can say that to perform an efficient, fast and precise alignment it is not enough to have only one alignment set. You will also need: the calibration steel shims BALTECH Series, calibration gauges BALTECH FG Series, self-adjusting chocking elements BALTECH DM, magnetic tripods with indicators, wrench set. BALTECH SA-PRO is the unique kit which contains all the tools required for the shaft alignment. The alignment of half- couplings, electric motors, pumps, gearboxes, compressors, fans, etc. can be performed with any BALTECH SA Series system and the tool kit BALTECH SA-PRO. The kit contains: BALTECH DM - self-adjusting chocking elements for the vertical machine movement; BALTECH FG - set of calibration gauges for the soft foot checking; BALTECH set of calibration shims for the shaft alignment; Device for a shaft cranking ; Laser distance meter for measurement of machine parameters

13 BALTECH Germany Spenglerstrasse Lübeck Tel: +49 (0) , Fax: +49 (0) , Internet: Russia St. Petersburg, , Chugunnaya, 40 Tel/fax: +7 (812) , Internet: Kazakhstan Astana city, Pobeda Avenue (Avenue Jenis) 79B, office number 408 Tel/fax: +7 (7172) , , , Internet: